Skip to content
Science

Performance3 min readBy Juan Manuel Rovira de Miguel

VBT on plate-loaded machines: how to measure velocity without a barbell

How to apply velocity-based training (VBT) on plate-loaded machines: what to measure, how to use velocity loss and which sensors work.

Velocity-based training (VBT) became popular with the barbell squat and bench press. But most strength work in a gym is done on plate-loaded and selectorised machines: leg press, leg extension, lat pulldown, row. Velocity can be measured there too, and it is even simpler.

VBT in two ideas

1. Velocity indicates effort. The heavier a load is relative to your maximum, the more slowly you move it. In the bench press, González-Badillo and Sánchez-Medina found an almost perfect relationship (R² = 0.98) between mean propulsive velocity and the percentage of the one-repetition maximum, and that relationship held even though participants improved their 1RM by 9.3% in six weeks.

2. Velocity loss indicates fatigue. Within a set, each repetition is a little slower. How much velocity is allowed to drop determines the type of adaptation. In a study by Pareja-Blanco et al., training the squat and stopping sets at a 20% velocity loss gave the same strength gain as going to 40%, with 40% fewer repetitions and a greater improvement in jumping (9.5% vs 3.5%). Going to 40% produced more hypertrophy, but also reduced the fastest fibres.

Why machines are a good place for VBT

  • The path is fixed. The machine guides the movement, so measured velocity is more stable from one repetition to the next than with free weights.
  • They are safe for getting close to failure. They make it possible to work with older adults, people in rehabilitation or beginners — exactly where controlling fatigue makes most sense.
  • They are what gets used most. In a fitness centre, measuring only the barbell leaves out most users.

What changes compared with the barbell

Velocity tables by %1RM were built with specific free-weight exercises and cannot be transferred as they are to a machine: each has its own path, pulley and friction. The solution is simple: build an individual profile for each machine and each person (we explain it in load-velocity profile) and, above all, use velocity loss within the set, which works the same in any exercise.

How to programme it in practice

  1. Warm-up with measurement. The velocity of the first repetitions with a known load shows how the person is doing that day. If it is clearly slower than usual, the load is adjusted.
  2. Choose the velocity loss according to the goal. 10–20% for strength and power with little fatigue; 30–40% when more volume and hypertrophy are the aim.
  3. End the set by velocity, not by number. Instead of “3 sets of 10”, “3 sets until a 20% loss”. Some days that will be 8 repetitions and others 12, depending on the person’s actual state.
  4. Record. Storing the velocity of the best repetition at each load lets you see progress without maximal tests.

Which sensor to use on a machine

Classic linear encoders have a cable that clips onto the bar. On a plate-loaded machine you have to find somewhere to anchor it and reposition it for every exercise, which is impractical in a gym with many machines.

PowerTrack is designed for this case: it attaches magnetically to the weight stack, with no cables or calibration, and also works with free weights. It measures velocity, range of motion, repetitions and fatigue in real time, and shows on your phone how velocity drops from one repetition to the next.

Free tool

1RM calculator from velocity (load-velocity profile): Enter 2 to 6 loads with the mean velocity of your best repetition at each. The calculator builds your load-velocity profile and estimates your 1RM and the loads for each percentage.

Frequently asked questions

Can velocity-based training (VBT) be done on machines?

Yes. Plate-loaded machines are well suited to VBT: the path is fixed, they are safer for getting close to failure and they are the most used equipment in a gym.

What velocity loss should be used to end a set?

10 to 20% for strength and power, and 30 to 40% for volume and hypertrophy.

Do %1RM velocity tables work on machines?

Not directly. It is recommended to build an individual load-velocity profile for each machine and each person.

What is the advantage of stopping the set at a 20% velocity loss?

In the squat, stopping at 20% gave the same strength gain as going to 40%, with 40% fewer repetitions and a greater improvement in jumping (Pareja-Blanco et al.).

References

  1. González-Badillo JJ, Sánchez-Medina L. Movement velocity as a measure of loading intensity in resistance training. Int J Sports Med, 2010.
  2. Pareja-Blanco F et al. Effects of velocity loss during resistance training on athletic performance, strength gains and muscle adaptations. Scand J Med Sci Sports, 2017.

Shall we show it at your facility?

We will show you the device in action, with no commitment, on-site or by video call.